Barrel Laser Mount

More Barrel Laser Mount

FAQ about Barrel Laser Mount

Laser and mount for my RWS 34 Panther? can anyone give me a link to buy an accurate laser that can mount to the barrel of my 34 panther i looked alot but cant find one that mounts to the barrel thanx check out pyramidair.com lots of selection on laser sights and mounts

Can someone give me some info on see-thru scope mounts and laser bore sighting a scope? If I set up a scope on my rifle using a SSI Laser Bore Sighting kit with my scope sitting on "see-thru mounts" (over & under mounts) at 25 feet as suggested by the kit then will my sights be on when I take a 100 yard shot out in the woods. I noticed that in the instructional video that the gun they are using is a rifle with "low mounts" on it. Also on the target that comes with the laser sight the mark above the bullseye is about 1 5/16 above the bullseye but the center of my scope sits about 2 1/18 of an inch above the center of the barrel. If I was using plain low mount scope mounts then the center of the scope would be a lot closer to the barrel. According to the instructions with the kit it says that when setting the target at 25 feet indoors that you site should be set for 100 yds. So with the above information does it make a difference the height of the scope (according to mounts) when using a SSI Laser Bore Sighting kit at 25 ft indoors and then making a 100 yd shot outdoors? Please understand that I already know that nothing is the same as actually shooting one outdoors with drift and trajectory. This is just a question to satisfy my need to know if scope height affects the end results when using a Laser Bore Sighting system indoors. Sure scope height makes a difference, the bore sighting at 25 feet it to get you hitting on target at 100 yard, it won't be dead on they are trying to get you to hit on paper so you can make the final adjustments.

Can I mount a laser to the side of my Yugo SKS? I have a Yugo SKS with a Tapco stock that has the bayonet cut. My problem is I already have an aftermarket receiver with a 4x scope, so I can't put a laser on the rail that is on my gas tube/hand guard because it would block the optic. Since I have a bayonet cut on the bottom of the stock there is no rail provided. I've searched the net for a way to attach another rail to the existing rail on my gas tube, but have only found pistol L rail attachments that I don't think would fit, or might make the scope useless (if they do fit without blocking the scope please let me know). Beside barrel mounted red lasers ( that I'm worried would easily rattle off target) does anybody know a way I can remedy this with out buying a new stock or spending a ton of money? I would also prefer a green laser because of the further distance and easier sight. Thanks I use a UTG high profile reciever cover with a weaver rail on top & a Leapers 4 X 32 scope.
Latest SKS high profile scope mount designed with raised integral Weaver style rail and AccuShot 1" tactical rings. 5 slots for flexible mounting positions. All steel construction. Easy to install. Simply replaces the receiver cover. Scope return to zero when reinstalled.

Light+Laser Mounts for an 870 Express Ribbed Barrel? I've been looking for a mount that will fit over the barrel of my 12 gauge 870 express synthetic, that is either single, or tri-rail, so I can mount either a laser, light, or both. The problem is the ribbed barrel kind of screws everything up, I can't find a barrel mount that would fit under the ribs. As well, I can't mount anything to the magazine tube, as it is only a 4 shell magazine, i e very short. Any ideas? Good Call< cheap too< will have to see how they hold under recoil. Have you tried a under barrel mount?

Will the Crosman 420 Laser Sight fit on my Crosman Pulse R71? I just recently bought the crosman pulse r71 and i am sure that anyone who has used or has seen this gun knows the "scope" that comes with it is actually the hopper system where you load the bb's. for this reason i need to buy a laser sight that will mount on the accessory rail under the gun barrel at the front. so would this laser sight work if not i could use some suggestions on other laser sights. any laser will fit, you just need to look at the size of the rail you put it on

How does a laser sight or a scope provide accuracy if...? ...they are mounted above, below or on the side of the barrel? Wouldn't that mean that the shooter would have to compensate of for the position of the laser dot or crosshairs. If the shooter were to shoot through the scope or at the position of the laser, that would mean the bullet would land either left, right, above or below the barrel assuming there are no environmental variables to consider (wind ,distance, drop, etc)

What gun is Tom Cruise using in the new movie "Knight & Day"? More specifically, the one that he is holding when he lands on top of the SUV occupied by Diaz and then shoots the following SUV. The gun has a squarred barrel and a mounted laser. it's like a big gun but not too big and it was going BANG! BANG! BANG! hope this helps

SKS Barrel Clamp Tri Rail tactical mount? This is a tactical rail mount that fits in between the gas tube and the barrel google for pics ok im looking for opinions from people who have one of these or have seen it work i have a norinco sks and id like to get this rail for it for a flashlight/laser but the barrel and gas tube look too close together for this to fit in between i see pictures of this on another sks on a website so im wondering if some modification will be needed opinions please also dont leave a comment griping me out for changing the stock no one cares what you think Personally, I'd never clamp anything on to the barrel, it would change point of bullet impact.
Barrels vibrate when you fire, clamping anything on to the barrel will change the harmonics of the barrel vibration, and i don't know if you'd be able to regulate the sights to the new pattern, I'm not even sure if the harmonics would even be consistent after clamping on additional hardware.
Doc

i would like to find a picatinny mounted laser sight for my glock 19? the big thing is, i want it small, and for it NOT to protrude beyond the end of the barrel when mounted. also, i don't want to spend a fortune. any recommendations? Just visit EBay.com. They have hundreds and hundreds of them listed in all different laser colors in the Sporting Goods>Hunting>Optics section.
Be sure to pay attention to what battery it uses, and, where it is coming from. You will probably get a better unit from someone who ships from the USA than HongKong.

What kind of aftermarket sights would you recommend for a Ruger GP-100 model 1704? and other than a grip laser can you use a barrel mounted laser on this firearm? I wouldn't use a grip laser, but that's just me.
I would, however, suggest that you replace the standard front sight with a fiber optic sight like this - http://www.google.com/imgres?imgurl=http://ecx.images-amazon.com/images/I/41kyjjTk-9L._SL500_AA300_.jpg&imgrefurl=http://www.amazon.com/HiViz-Ruger-GP100-Fiber-Optic/dp/B000EBUG4K&usg=__spBSb3uJ-lltvVPU0WwsAqJGddo=&h=300&w=300&sz=10&hl=en&start=0&zoom=1&tbnid=rTmwMNkudWewQM:&tbnh=130&tbnw=128&ei=1_aETaeGGaHg0gGl9L29CA&prev=/images%3Fq%3Druger%2Bgp100%2Bfiber%2Boptic%26um%3D1%26hl%3Den%26biw%3D1260%26bih%3D538%26tbs%3Disch:1&um=1&itbs=1&iact=rc&dur=421&oei=1_aETaeGGaHg0gGl9L29CA&page=1&ndsp=21&ved=1t:429,r:0,s:0&tx=66&ty=61
The regular front sight is difficult to see in low light condition.

Barrel Laser Mount is from category: Flashlights.